检索结果-南通市图书馆

Journal of Central South University 2024年第6期31卷 1774-1789页

作者： ZHANG Jin-hai NIE Kai-bo ZHANG Jin-hua deng kun-kun LIU Zhi-long College of Materials Science and Engineering Taiyuan University of TechnologyTaiyuan 030024China State Key Laboratory of High-end Compressor and System Technology Hefei 230031China

In this study,the Mg-3Zn-0.5Zr-χNd(χ=0,0.6)alloys were subjected to final rolling treatment with large deformation of 50%.The impact of annealing temperatures on the microstructure and mechanical properties was *** rolled Mg-3Zn-0.5Zr-0.6Nd alloy exhibited an ultimate tensile strength of 386 MPa,a yield strength of 361 MPa,and an elongation of 7.1%.Annealing at different temperatures resulted in reduced strength and obviously increased elongation for both *** mechanical properties for the Mg-3Zn-0.5Zr-0.6Nd alloy were achieved after annealing at 200℃,with an ultimate tensile strength of 287 MPa,a yield strength of 235 MPa,and an elongation of 26.1%.The numerous deformed microstructures,twins,and precipitated phases in the rolled alloy could impede the deformation at room temperature and increase the work hardening *** annealing,a decrease in the work hardening effect and an increase in the dynamic recovery effect were obtained due to the formation of fine equiaxed grains,and the increased volume fraction of precipitated phases,which significantly improved the elongation of the ***,the addition of Nd element could enhance the annealing recrystallization rate,reduce the Schmid factor difference between basal and prismatic slip systems,facilitate multi-system slip initiation and improve the alloy plasticity.

关键词： Mg-Zn-Zr-Nd alloy large final rolling deformation annealing temperatures microstructures mechanical properties

固溶处理对6061铝合金显微组织与力学性能的影响

在线全文

学校读者我要写书评

暂无评论

材料热处理学报 2024年第8期45卷 41-47页

作者：史权新邓坤坤聂凯波林涛梅表闹太原理工大学材料科学与工程学院山西太原030024 太原理工大学分析测试中心山西太原030024 浙江宏鑫科技股份有限公司浙江台州317000

采用光学显微镜(OM)、电子背散射衍射(EBSD)和维氏显微硬度计研究了固溶处理对压缩态6061铝合金显微组织与力学性能的影响。结果表明:压缩态6061铝合金经过固溶处理后有细小等轴再结晶晶粒形成,再结晶晶粒的形成弱化了其织构强度。随着... 详细信息

采用光学显微镜(OM)、电子背散射衍射(EBSD)和维氏显微硬度计研究了固溶处理对压缩态6061铝合金显微组织与力学性能的影响。结果表明:压缩态6061铝合金经过固溶处理后有细小等轴再结晶晶粒形成,再结晶晶粒的形成弱化了其织构强度。随着固溶处理时间增加,合金中的再结晶晶粒增多,织构强度降低。6061铝合金经过固溶处理后由于固溶强化的作用导致其硬度显著增大,但随着固溶处理时间的增加,合金的晶粒尺寸增大,细晶强化作用降低,致使合金的硬度值有所减小。

关键词： 6061铝合金固溶处理显微组织显微硬度

Effect of Ti_(p) Content on the Work Hardening and Softening Behavior of Mg-Zn-Ca Alloy

在线全文

学校读者我要写书评

暂无评论

Acta Metallurgica Sinica(English Letters) 2024年第3期37卷 551-560页

作者： Jin-Kai Zhang Cui-Ju Wang Yi-Dan Fan Chao Xu Kai-Bo Nie kun-kun deng Shanxi Key Laboratory of Advanced Magnesium-Based Materials College of Materials Science and EngineeringTaiyuan University of TechnologyTaiyuan 030024China School of Materials Science and Engineering Harbin Institute of TechnologyHarbin 150001China

The Ti_(p)/ZX60 composites with different Ti_(p) contents were prepared by semi-solid stirring *** extrusion,the microstructure,work hardening and softening behavior of the Ti_(p)/ZX60 composites were analyzed compared with the ZX60(Mg-6Zn-0.2Ca)*** results showed that the addition of Ti_(p) could not only promote the nucleation of dynamic recrystallized(DRXed)grains,but also be propitious to the refinement of DRXed *** increasing Ti_(p) content,the size of DRXed grains decreased accompanied with increasing volume fraction of DRXed *** the Ti_(p) content increased to 15 vol.%,the average size and volume fraction of DRXed grains reached to~0.32μm and 93.2%,***,both the strength and elongation were improved by the addition of Ti_(p).With increasing content of Ti_(p),a substantial increase in the strength was achieved with little change in the ***,the elongation decreased sharply when the Ti_(p) content further increased to 15 vol.%.The addition of Ti_(p) led to an increase in the work hardening rate,which gradually increased with increasing Ti_(p) ***,the softening rate did not demonstrate the same tendency with increasing Ti_(p) *** the conventional ceramic particles,the Ti_(p) can be deformed in coordination with the matrix alloy,which imparted a higher softening rate to the matrix *** though the softening rate improved as the Ti_(p) content increased from 5 to 10 vol.%,it dropped deeply as the Ti_(p) content increased to 15 vol.%owing to the fracture of Ti_(p) during extrusion.

关键词： Titanium particle content Particle reinforced magnesium matrix composites Work hardening Softening behavior Mechanical properties

Highly efficient CO_(2) capture using 2-methylimidazole aqueous solution on laboratory and pilot-scale

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Chinese Journal of Chemical Engineering 2024年第3期67卷 148-156页

作者： kun Li Han Tang Shuangshuang Li Zixuan Huang Bei Liu Chun deng Changyu Sun Guangjin Chen State Key Laboratory of Heavy Oil Processing China University of PetroleumBeijing 102249China Zhejiang Tiandi Environmental Protection Technology Co. Ltd.Hangzhou 310012China

To date,the primary industrial carbon capture approach is still absorption using aqueous solutions of ***,to pursue a substitute for the amine-based approach to improve the CO_(2) capture efficiency and decrease the energy cost further,we report a new carbon capture approach using a 2-methylimidazole(mIm)aqueous *** properties and sorption behaviors of this approach have been experimentally *** results show that the mIm solution has higher CO_(2) absorption capacity under relatively higher equilibrium pressure(>130 kPa)and lower desorption heat than the methyldiethanolamine solution.91.6%sorption capacity of mIm solution can be recovered at 353.15 K and 80 *** selectivity for CO_(2)/N_(2) and CO_(2)/CH_(4) can reach an exceptional 7609 and 4324,***,the pilot-scale tests were also performed,and the results demonstrate that more than 98%of CO_(2) in the feed gas could be removed and cyclic absorption capacity can reach 1 mol·L^(-1).This work indicates that mIm is an excellent alternative to alkanolamines for carbon capture in the industry.

关键词： CO_(2) capture Absorption 2-Methylimidazole Separation Pilot-scale tests

Study on hydrodynamic diffusion law of the swelling particle slurry in karst pipeline

在线全文

学校读者我要写书评

暂无评论

Particuology 2024年第4期87卷 218-231页

作者： Bingchuan Cheng Haibo Li Guangming Pan Runhuai deng Yu'an Gong Shujun Xu kun Zhou Zhuo Zheng School of Civil Engineering Geotechnical and Structural Engineering Research CenterShandong UniversityJinan250061China The Fourth Prospecting of Shandong Coal Geology Bureau Weifang261000China China Railway 14th Bureau Group Corporation Limited Jinan250101China School of Trafic Engineering Shandong Jianzhu University.Fengming RoadLingang Development ZoneJinan250101China

The swelling particle grouting material has demonstrated remarkable plugging effectiveness in high-pressure and large-flow burst water within karst ***,current research on the rheolog-ical model,flow computation theory,and plugging mechanism of this material is *** conven-tional grouting slurry diffusion process,using the liquid-liquid two-phase flow method,fails to accurately simulate high solubility slurry and particle *** address these limitations,this study established a precise constitutive model to describe the swelling particle slurry diffusion process in dynamic ***,a coupling calculation method was proposed to analyze the spatiotemporal heterogeneity of viscosity during slurry diffusion by considering the migration of slurry and the changes in *** investigate the interaction between particle swelling and flow field changes,a Compu-tational Fluid Dynamics-Discrete Element Method(CFD-DEM)coupling model was developed for the diffusion of swelling particle *** is demonstrated that slurry viscosity increases exponentially within the diffusion front as the particle swelling rate rises,and the drag force exhibits an intriguing behavior of initially increasing and then decreasing as the slurry flows through the ***-more,the CFD-DEM coupling model proved to be more accurate in describing viscosity distribution and diffusion distance compared to the finite element *** primary objective of this paper is to reveal the plugging mechanism and provide theoretical support for the engineering application of the swelling particle grouting material.

关键词： Karst pipeline Swelling particle grouting material Dynamic water diffusion Spatiotemporal variation of viscosity CFD-DEM coupling model

Low-concentration and multi-component NMHCs capture from oil field exhaust using porous ZIF-8/iso-hexadecane slurry

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Green Chemical Engineering 2024年第2期5卷 245-256页

作者： kun Li Han Tang Jin Cai Chun deng Bei Liu Yunlei Peng Changyu Sun Guangjin Chen State Key Laboratory of Heavy Oil Processing China University of PetroleumBeijing102249China

Non-methane hydrocarbons(NMHCs)are a common type of volatile organic compounds(VOCs)pollutant in the petrochemical industry and have attracted widespread attention because of their adverse health effects and environmental *** this paper,we report a new porous slurry formed with zeolitic imidazolate framework-8(ZIF-8)and iso-hexadecane to capture the low-concentration and multi-component NMHCs(mainly ethane(C_(2)H_(6)),propane(C_(3)H_(8)),and n-butane(n-C_(4)H_(10)))from the oil field *** sorption capacity of C_(2)H_(6)in the slurry is significantly higher than that of nitrogen(N_(2))and methane(CH_(4)).Moreover,the slurry demonstrated a clear advantage for C_(2)H_(6)over N_(2)and CH_(4)in competitive adsorption through the pressure-drop *** the NMHCs capture experiments,the C_(3)H_(8)and n-C_(4)H_(10)concentrations after purification can be reduced to below 100 ppm,while the C_(2)H_(6)concentration can reach approximately 180 *** encouragingly,in the breakthrough tests,the slurry exhibits a perfect kinetic separation selectivity for multi-component ***,to avoid structural collapse of ZIF-8 material during long-term use in acidic and wet environments,a certain amount of 2-methylimidazole was retained in the slurry as a protective agent in the material synthesis *** this way,the ZIF-8 materials in the slurry can retain the stable characteristic structure in an aqueous and acidic environment and keep the capture capacity for NMHCs without *** believe the porous ZIF-8/iso-hexadecane slurry is a promising capture agent for low-concentration and multi-component NMHCs with strong purification capacity and stability.

关键词： VOCs capture NMHCs capture MOFs ZIF-8 Porous slurry

Sm-like 5 knockdown inhibits proliferation and promotes apoptosis of colon cancer cells by upregulating p53,CDKN1A and TNFRSF10B

在线全文

学校读者我要写书评

暂无评论

World Journal of Gastrointestinal Oncology 2024年第6期16卷 2716-2726页

作者： Cai-Jing Mo Xiao-Yuan deng Ru-Lan Ma kun Zhu Lei Shi Kang Li Department of Surgical Oncology The First Affiliated Hospital of Xi’an Jiaotong UniversityXi’an 710061Shaanxi ProvinceChina Department of Infectious Diseases The First Affiliated Hospital of Xi’an Jiaotong UniversityXi’an 710061Shaanxi ProvinceChina

BACKGROUND The role of Sm-like 5(LSM5)in colon cancer has not been *** this study,we investigated the role of LSM5 in progression of colon cancer and the potential underlying mechanism *** To determine the role of LSM5 in the progression of colon cancer and the potential underlying mechanism *** The Gene Expression Profiling Interactive Analysis database and the Human Protein Atlas website were used for LSM5 expression analysis and prognosis ***-time quantitative polymerase chain reaction and Western blotting were utilized to detect the expression of mRNAs and proteins.A lentivirus targeting LSM5 was constructed and transfected into colon cancer cells to silence LSM5 *** and apoptosis assays were also conducted to evaluate the growth of the colon cancer *** GeneChip assay and bioinformatics analysis were performed to identify the potential underlying mechanism of LSM5 in colon *** LSM5 was highly expressed in tumor tissue and colon cancer cells.A high expression level of LSM5 was related to poor prognosis in patients with colon *** of LSM5 suppressed proliferation and promoted apoptosis in colon cancer *** of LSM5 also facilitates the expression of p53,cyclin-dependent kinase inhibitor 1A(CDKN1A)and tumor necrosis factor receptor superfamily 10B(TNFRSF10B).The inhibitory effect of LSM5 knockdown on the growth of colon cancer cells was associated with the upregulation of p53,CDKN1A and *** LSM5 knockdown inhibited the proliferation and facilitated the apoptosis of colon cancer cells by upregulating p53,CDKN1A and TNFRSF10B.

关键词： Sm-like 5 Colon cancer Proliferation Apoptosis Knockdown

Super P and MoO_(2)/MoS_(2)co-doped gradient nanofiber membrane as multi-functional separator for lithium–sulfur batteries

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Rare Metals 2024年第9期43卷 4263-4273页

作者： Xin Liang Dong-Qing Zhao Qian-Qian Huang Sheng Liang Li-Li Wang Lei Hu Ling-Li Liu kun-Hong Hu Chong-Hai deng Sheng Cheng Er-Tao Zhu Hua-Xia deng School of Energy Materials and Chemical Engineering LIB Technology Center of Anhui ProvinceHefei UniversityHefei 230601China Instrumental Analysis Centre Hefei University of TechnologyHefei 230009China Hefei Youngy Energy Materials Co. Ltd.Hefei 230000China Department of Modern Mechanics University of Science and Technology of ChinaHefei 230026China

Lithium-sulfur battery is one of the most promising battery systems for industrialization due to its high theoretical specific capacity and high energy ***,the"shuttle effect"has restrained the advancement of lithium-sulfur *** this work,a gradient-structured nanofiber membrane with pure gelatin on one side and Super P-MoO_(2)/MoS_(2)-gelatin on the other side was created using a multi-step electrostatic spinning technique,which was applied for multi-functional separator for lithium-sulfur *** pure gelatin layer facing the anode side primarily homogenizes the lithium flux,whereas the Super P-MoO_(2)/MoS_(2)-gelatin layer facing the cathode side primarily adsorbs polysulfides by physical and chemical adsorption and enhancing polysulfide conversion *** findings demonstrate that even after 150 cycles at 0.2C,the lithium-sulfur battery can still sustain a discharge-specific capacity of 572.3 mAh·g^(-1).When used with Li||Li symmetric batteries,it has a cycle life of more than 1200 *** commercialization of lithium-sulfur batteries is given a fresh idea by this straightforward preparation technique.

关键词： MoO_(2)/MoS_(2) Nanofiber Membrane Li-S battery

Current-perpendicular-to-plane transport properties of 2D ferromagnetic material CrTe_(2)

在线全文

学校读者我要写书评

暂无评论

Chinese Physics B 2024年第9期33卷 535-539页

作者： Jin Wang Yu Liu Taikun Wang Yongkang Xu ShuanghaiWang kun He Yafeng deng Pengfei Yan Liang He School of Electronic Science and Engineering Nanjing UniversityNanjing 210023China State Key Laboratory of Spintronics Nanjing UniversitySuzhou 215163China

Heterostructures of van der Waals(vdW)ferromagnetic materials have become a focal point in research of lowdimensional spintronic *** current direction in spin valves is commonly perpendicular to the plane(CPP).However,the transport properties of the CPP mode remain largely *** this work,current-in-plane(CIP)mode and CPP mode for CrTe_(2) thin films are carefully *** temperature-dependent longitudinal resistance transitions from metallic(CIP)to semiconductor behavior(CPP),with the electrical resistivity of CPP increased by five orders of *** importantly,the transport properties of the CPP can be categorized into a single-gap tunneling-through model with the activation energy(Ea)of1.34 meV/gap at 300–150 K,the variable range hopping model with a linear negative magnetoresistance at 150–20 K,and weak localization region with a nonlinear magnetic resistance below 20 *** study explores the vertical transport in CrTe_(2) materials for the first time,contributing to understand its unique properties and to pave the way for its potential in spin valve devices.

关键词： 2D vdW CrTe_(2) current-perpendicular-to-plane negative magnetic resistance

A hybrid machine learning optimization algorithm for multivariable pore pressure prediction

在线全文

学校读者我要写书评

暂无评论

Petroleum Science 2024年第1期21卷 535-550页

作者： Song deng Hao-Yu Pan Hai-Ge Wang Shou-kun Xu Xiao-Peng Yan Chao-Wei Li Ming-Guo Peng Hao-Ping Peng Lin Shi Meng Cui Fei Zhao School of Petroleum and Natural Gas Engineering Changzhou UniversityChangzhou213164JiangsuChina Tubular Goods Research Institute of CNPC Beijing102249China CNPC Engineering Technology R&D Company Limited Beijing102206China

Pore pressure is essential data in drilling design,and its accurate prediction is necessary to ensure drilling safety and improve drilling *** methods for predicting pore pressure are limited when forming particular structures and *** this paper,a machine learning algorithm and effective stress theorem are used to establish the transformation model between rock physical parameters and pore *** study collects data from three *** 1 had 881 data sets for model training,and Wells 2 and 3 had 538 and 464 data sets for model *** this paper,support vector machine(SVM),random forest(RF),extreme gradient boosting(XGB),and multilayer perceptron(MLP)are selected as the machine learning algorithms for pore pressure *** addition,this paper uses the grey wolf optimization(GWO)algorithm,particle swarm optimization(PSO)algorithm,sparrow search algorithm(SSA),and bat algorithm(BA)to establish a hybrid machine learning optimization algorithm,and proposes an improved grey wolf optimization(IGWO)*** IGWO-MLP model obtained the minimum root mean square error(RMSE)by using the 5-fold cross-validation method for the training *** the pore pressure data in Well 2 and Well 3,the coefficients of determination(R^(2))of SVM,RF,XGB,and MLP are 0.9930 and 0.9446,0.9943 and 0.9472,0.9945 and 0.9488,0.9949 and *** achieves optimal performance on both training and test data,and the MLP model shows a high degree of *** indicates that the IGWO-MLP is an excellent predictor of pore pressure and can be used to predict pore pressure.

关键词： Pore pressure Grey wolf optimization Multilayer perceptron Effective stress Machine learning