检索结果-南通市图书馆

Experimental Study on Latent Heat Storage Characteristics of W/O Emulsion-Supercooling Rate of Dispersed Water Drops by Direct Contact Heat Exchange

引用

Journal of Thermal Science 2013年第2期22卷 145-151页

作者： Shin-ichi Morita Yasutaka Hayamizu akihiko horibe Naoto Haruki Hideo Inaba Department of Mechanical Engineering Yonago National College of Technology Graduate School of Natural Science and Technology Okayama University Tsuyama National College of Technology

Recently, much attention has been paid to investigate the latent heat storage system. Using of ice heat storage system brings an equalization of electric power demand, because it will solved the electric -power-demand-concentration on day-time of summer by the air conditioning. The flowable latent heat storage material, Oil/Water type emulsion, microencapsulated latent heat material-water mixture or ice slurry, etc., is enable to transport the latent heat in a pipe. The flowable latent heat storage material can realize the pipe size reduction and system efficiency improvement. Supercooling phenomenon of the dispersed latent heat storage material in continuous phase brings the obstruction of latent heat storage. The latent heat storage rates of dispersed water drops in W/O (Water/Oil) emulsion are investigated experimentally in this study. The water drops in emulsion has the diameter within 3 ~ 25μm, the averaged water drop diameter is 7.3μm and the standard deviation is 2.9μm. The direct contact heat exchange method is chosen as the phase change rate evaluation of water drops in W/O emulsion. The supercooled temperature and the cooling rate are set as parameters of this study. The evaluation is performed by comparison between the results of this study and the past research. The obtained experimental result is shown that the 35K or more degree from melting point brings 100% latent heat storage rate of W/O emulsion. It was clarified that the supercooling rate of dispersed water particles in emulsion shows the larger value than that of the bulk water.

关键词：潜热储能过冷现象冷却速率直接接触散水实验储能特性滴眼液

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Study of Cycle Output Improvement by Work-Fluid Including Phase Change Material

引用

Journal of Thermal Science 2016年第6期25卷 558-563页

作者： Shin-ichi MORITA Kota TANIMURA Yasutaka HAYAMIZU Takanobu YAMADA akihiko horibe Naoto HARUKI Toshiaki SETOGUCHI Department of Mechanical Engineering National Institute of TechnologyYonago College Three S Techno Corporation Tottori factory Department of Mechanical Engineering Kitami Institute of Technology Graduate School of Natural Science and Technology Okayama University Department of Advanced Technology Fusion Saga University

This paper deals with the output improvement of heating and cooling cycle by using the work-fluid including phase change material.The experimental study is carried out by heat exchange between work-fluid and heat transfer surface.The work-fluid is flown to a high temperature or a low temperature heat transfer surface from the narrow path.In order to increase the amount of the heat transmission,a trace of Diethylether(boiling point 34.8 ℃),as a phase change material(PCM),is added to the work-fluid.The parameters of the experiment are additive amount of PCM,the rotational speed of the displacer piston and the temperature of heat transfer surface.It is clarified that the increasing of engine cycle output is brought by the PCM addition.The effect of PCM addition is evaluated by output ratio which is defined from the experimental cycle output data.The requirements for acquiring the increasing effect of output by adding PCM are clarified.

关键词：分阶段执行变化材料加热转移产量改进低温度差别引擎

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Melting and Solidification Heat Transfer Characteristics of a Phase-Change Material in a Latent Heat Storage Vessel: Effects of a Perforated Partition Plate and Metal Fiber

引用

Journal of Power and Energy Engineering 2017年第8期5卷 13-29页

作者： Than Tun Naing akihiko horibe Naoto Haruki Yutaka Yamada Graduate School of Natural Science and Technology Okayama University Okayama Japan Department of Human Information Engineering Okayama Prefectural University Okayama Japan

Today, latent heat storage technology has advanced to allow reuse of waste heat in the middle-temperature range. This paper describes an approach to develop a latent heat storage system using middle-temperature waste heat (~100oC - 200oC) from factories. Direct contact melting and solidification behavior between a heat-transfer fluid (oil) and a latent heat storage material mixture were observed. The mixture consisted of mannitol and erythritol (Cm = 70 mass %, Ce = 30 mass %) as a phase-change material (PCM). The weight of the PCM was 3.0 kg and the flow rate of the oil, foil, was 1.0, 1.5, or 2.0 kg/min. To decrease the solidified height of the PCM mixture during the solidification process, a perforated partition plate was installed in the PCM region in the heat storage vessel. PCM coated oil droplets were broken by the perforated partition plate, preventing the solidified height of the PCM from increasing. The solidification and melting processes were repeated using metal fiber. It was found that installing the metal fiber was more effective than installing the perforated partition plate to prevent the flow out problem of the PCM.

关键词： Heat Storage Vessel Solidified Height Phase-Change Material (PCM) Mixture Perforated Partition Plate Metal Fiber

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Experimental Study on Latent Heat Storage Characteristics of W/O Emulsion by Ultrasonic Wave Impression

引用

Open Journal of Fluid Dynamics 2013年第2期3卷 48-54页

作者： Shin-ichi Morita Yasutaka Hayamizu akihiko horibe Naoto Haruki Hideo Inaba Issei Higashi Department of Mechanical Engineering Yonago National College of Technology Yonago Japan Edit Inc. Fukuoka Japan Graduate School of Natural Science and Technology Okayama University Okayama Japan Shujitsu University Okayama Japan

The flowable latent heat storage material like Oil/Water type emulsion, microencapsulated latent heat material-water mixture or ice slurry, etc., is enabled to transport the latent heat in a pipe. Supercooling phenomenon of the dispersed latent heat storage material in continuous phase is obstructed by a latent heat storage. The latent heat storage rates of dispersed waterdrops in W/O (Water/Oil) emulsion are investigated experimentally in this study. The waterdrops in emulsion have the diameter within 3 - 25 μm, the averaged diameter of waterdrops is 7.3 μm and the standard deviation is 2.9 μm. Supercooling release of waterdrops in emulsion is examined by short time impressing of the ultrasonic. The direct contact heat exchange method is chosen as the phase change rate evaluation of waterdrops in W/O emulsion. The supercooled temperature is set as parameters of this study. The previous obtained experimental result, as the condition without impressing ultrasonic wave, showed that the 35 K or more degree from melting point brings 100% latent heat storage rate of W/O emulsion. It is clarified that it is possible to reduce 20 K of supercooling degree by impressing the ultrasonic.

关键词： Heat Storage Latent Heat W/O Emulsion Direct Contact Heat Exchange Ultrasonic

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Heat Transfer Characteristics of Work Fluid Including Phase Change Material That Flow into Heating Surface from Narrow Path

引用

Open Journal of Fluid Dynamics 2014年第5期4卷 454-462页

作者： Shin-Ichi Morita Yasutaka Hayamizu Takanobu Yamada akihiko horibe Naoto Haruki Toshiaki Setoguchi Kazuma Adachi Department of Mechanical Engineering National Institute of Technology Yonago College Yonago Japan Department of Mechanical Engineering Kitami Institute of Technology Kitami Japan Graduate School of Natural Science and Technology Okayama University Okayama Japan Department of Advanced Technology Fusion Saga University Saga Japan Graduate School of Machine Creative Engineering Nagaoka University of Technology Nagaoka Japan

Use of the low temperature (less than 100°C) energy contributes to effective use of heat resources. The cost recovery by power generation is difficult by using an existing system (the binary cycle or the thermoelectric conversion element), because the initial investment is large. The final purpose of this research is development of the low temperature difference drive engine supposing use in a hot-springs resort as a power source for electric power generation. In order that a traveler may look at and delight a motion of an engine, it is made to drive at low-speed number of rotations. An engine cycle of this study is aimed at the development of Stirling cycle engine which can maintain high efficiency in small size. This kind of engine has simple structure;it brings low cost, and it is easy to perform maintenance. However, it is difficult to obtain enough output by this type of engine, because of its low temperature difference. This paper deals with the heat transfer characteristic that the working fluid including a phase change material flows into the heating surface from the narrow path. In order to increase the amount of the heat transmission, Diethylether is added to the working fluid. Diethylether is selected as a phase change material (PCM) that has the boiling point which exists between the heat source of high temperature and low temperature. The parameters of the experiment are additive amount of PCM, rotational speed of the displacer piston and temperature of heat transfer surface. It is shown that it is possible to make exchange of heat amount increase by adding phase change material. The result of this research shows the optimal condition of the difference in temperature in heat processing, number of revolutions, and addition concentration of PCM.

关键词： Phase Change Material Heat Transfer Low Temperature Difference Working Fluid

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：