检索结果-南通市图书馆

Experimental study on upward bubble velocity and pierce length distributions in a water model of co.per co.verter

在线全文

学校读者我要写书评

暂无评论

Journal of University of Science and technology beijing 2003年第6期10卷 16-21页

作者： Bin Du, Jiayun Zhang, Tuping Zhou, and Qifeng ShuMetallurgical Engineering School, University of Science and technology beijing, beijing 100083, chinaLegend co. ltd., beijing 100085, china Metall. Eng. Sch. Univ. of Sci. and Technol. Beijing Beijing 100083 China Legend co. ltd. Beijing 100085 China

The upward bubble velocity and the pierce length distributions in a sectionalwater model of the co.per co.verter in Guixi Smelter in Jiangxi, china, were measured using atwo-co.tact electro-resistivity probe. In the case of using a single tuyere, the bubble velocitydistribution along longitudinal direction was similar to that derived from Guassian function. Beyondthe center of the longitudinal range, the bubble pierce length exhibited a sudden increase. Theupward bubble velocity at a specified location co.ld go up to meters per seco.d. Its probability ata fixed location obeys a lognormal function; the bubble pierce length there varies bellow a fewcentimeters. In the case of using multi-tuyeres, the upward bubble velocity was roughly uniformright above the tuyeres and showed a slow decrease beyond this region. The bubble pierce lengthwithin both of these two regions was roughly uniform. Its average value in the former region,however, was found to he somewhat lower than that in the later.

关键词： upward bubble velocity bubble pierce length distribution co.per co.verter

A novel method for the improvement of power efficiency in high peak-to-average-power ratio co.munication systems

在线全文

学校读者我要写书评

暂无评论

Science china(Information Sciences) 2010年第8期53卷 1697-1702页

作者： REN ZhiYuan 1 , ZHANG HaiLin 1 & GUO Kai 2 1 State Key Laboratory of Integrated Services Network, Xidian University, Xi’an 710071, china 2 Aerospace Long March Launch Vehicle technology co. ltd., beijing 100076, china State Key Laboratory of Integrated Services Network Xidian University Xi’an China Aerospace Long March Launch Vehicle technology co. ltd. Beijing China

To solve the problem of low power efficiency of power amplifiers (PA) in the high peak-to-averagepower ratio (PAPR) co.munication system, a novel signal deco.posed amplifier structure has been proposed in order to decrease the energy co.sumption and increase the power efficiency of PA. The high PAPR signal can be deco.posed into several low PAPR branch signals, linearized and amplified in parallel. This structure can reduce the PAPR of branch signals and improve the power efficiency of PA. The simulation results indicate that the power efficiency will be remarkably increased.

关键词： Green Radio power amplifier signal deco.posed

Investigation on the co.per co.tent of Matte Smelting Slag in Peirce-Smith co.verter

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

Journal of University of Science and technology beijing 2001年第3期8卷 177-181页

作者： Chunlin Chen, Jiayun Zhang, Meng Bai, Shoukun Wei Metallurgy School, University of Science & technology beijing, beijing 100083, china Guixi Smelter, Jiangxi co.per co. ltd., Jiangxi 335424, china Metallurgy School Univ. of Sci. and Tech. Beijing Beijing 100083 China

The co.per co.tents and its existing forms in the slags during the slag-making stage of Peirce-Smith co.verters in Guixi Smelter, Jiangxi Province, china have been investigated. The investigation was based on plant trials with the co.responding thermodynamic calculations and kinetic co.siderations. From the plant data, the total co.per co.tent in the slags was in the range of 2% to 8% (mass fraction). The mechanical entrainment of matte drops has been found to be the main cause of the co.per loss. The suspension index, defined as the ratio of the mass fraction of co.per in suspended matte drops in the slag to that in bulk of the matte phase, has been adopted to quantify the matte entrainment. The values of this parameter estimated in this work have been found mainly within a range of 2.5%-8.0%. The Fe3O4 co.tent in the slag has been estimated to be the most important factor, among others, influencing the separation of slag with matte and, co.sequently, the co.per loss from the slag.

关键词： Peirce-Smith co.verter co.per co.tent molten slag

co.struction of High-Efficiency and Low-co.t Clean Steel Production System in Shougang Jingtang

在线全文

学校读者我要写书评

暂无评论

Journal of Iron and Steel Research International 2011年第S2期18卷 42-51页

作者： ZHANG Fu-ming,CUI Xing-chao,ZHANG De-guo(beijing Shougang International Engineering technology co.,ltd.,beijing 100043,china) beijing Shougang Int Engn Technol co.ltd Beijing 100043 Peoples R China

This paper analyzes the technology for clean steel production in modern iron and steel plant,a philosophy with production efficiency,manufacturing co.t and product performance in its *** also makes a review on functions of high-efficiency,low-co.t and high-quality steel products manufactured by the new generation iron and steel plant,in co.bination with the study on design of steelmaking-co.tinuous casting process of Shougang Jingtang iron and steel *** applying precise and dynamic design system to optimize and allocate systems and working procedures of hot metal pretreatment,co.verter smelting,seco.dary refining,co.tinuous casting process,etc,a platform of high-efficiency,low-co.t and high-quality clean steel production is built.

关键词： steelmaking co.tinuous casting clean steel hot metal pretreatment seco.dary refining

Process optimization of reaction of acid leaching residue of asbestos tailing and sodium hydroxide aqueous solution

在线全文

学校读者我要写书评

暂无评论

Science china(Technological Sciences) 2009年第1期52卷 204-209页

作者： DU GaoXiang1,3, ZHENG ShuiLin2 & DING Hao1 1 School of Materials Science and technology, china University of Geosciences (beijing), beijing, 100083, china 2 School of Chemical and Environment Engineering, china University of Mining and technology (beijing), beijing 100083, china 3 Hebei Qinghe Refractory Group co. ltd., Xingtai 054804, china School of Materials Science and technology China University of Geosciences (Beijing) Beijing China Hebei Qinghe Refractory Group co. ltd. Xingtai China School of Chemical and Environment Engineering China University of Mining and Technology (Beijing) Beijing China

Silica is the major co.ponent of the acid leaching residue of asbestos tailing. The waterglass solution can be prepared by the reaction of the residue with sodium hydroxide aqueous solution. co.pared to the high temperature reaction method, this process is environmental friendly and low co.t. In this paper, the reaction process of the residue and the sodium hydroxide aqueous solution is optimized. The optimum reaction process parameters are as follows: the usage of sodium hydroxide is 26.4 g/100 g acid leaching residue, the reaction temperature is 90℃, the reaction time is 1 h, and the ratio of the liquid/solid is 2.0. The significance sequence of the process parameters to the alkali leaching reaction effect is the usage of sodium hydroxide > the ratio of the liquid/solid > the reaction time > the reaction temperature. The significance sequence to the leaching ratio of SiO2 is the ratio of the liquid/solid > the usage of sodium hydroxide > the reaction time > the reaction temperature. The significance sequence to the modulus of the sodium silicate is the ratio of the liquid/solid > the usage of sodium hydroxide > the reaction time > the reaction temperature. Under the optimum co.ditions, the leaching ratio of the SiO2 is 77.5%, and the modulus of the sodium silicate is 3.15. The XRD analysis result indicates that the major co.ponents of the alkali leaching residue are serpentine, talc, quartz and some albite.

关键词： asbestos tailing acid leaching residue sodium hydroxide process optimization

Improved hydrogenation-dehydrogenation characteristics of nanostructured melt-spun Mg-10Ni-2Mm alloy processed by rapid solidification

在线全文

学校读者我要写书评

暂无评论

Progress in Natural Science:Materials International 2010年第1期20卷 49-53页

作者： Na XING,Ying WU,Wei HAN,Shao-xiong ZHOU china Iron & Steel Research Group,Advanced technology & Materials co.,ltd.,beijing 100081,china china Iron & Steel Research Group Advanced Technology & Materials Co. Ltd. Beijing 100081 China

The as-cast Mg-10Ni-2Mm(mole fraction,%)alloy was prepared by a simple and low-co.t two-step method of pre-alloying and vacuum induction *** nanocrystalline alloy was obtained by the melt-spun process with the surface velocity of co.per wheel of 10.5 m/*** hydrogen storage properties were examined by PCT *** enthalpy(ΔH)and entropy(ΔS)of the alloy determined by van’t Hoff plots indicate that the thermodynamic performance of the nanocrystalline alloy is improved by fast diffusion ability of hydrogen in the nanocrystalline microstructure embedding nano-particles of intermetallics co.pounds Mg2Ni and *** reaction kinetics of the melt-spun alloy is greatly improved due to short diffusion path of hydrogen in the nanocrystalline microstructure,resulting in better overall hydrogen storage *** hydrogen storage capacity is 5.09%(mass fraction,hereinafter the same),and the amount of hydrogen desorption is 4.86%.The hydrogen desorption rate of 95.5%in the alloy is available.

关键词： Mg-10Ni-2Mn alloy vacuum induction melting melt-spun hydrogen storage properties enthalpy entropy kinetics

Force Parameter Model of 3-Roll Mills for co.tinuous co.d Rolling Wires

在线全文

同方期刊数据库

学校读者我要写书评

暂无评论

International Journal of Minerals,Metallurgy and Materials 1999年第4期13卷 292-295页

作者： Baolong Zheng1 Li Sun2 Ruichen An2 Jin Wang1 Weichang Zhu1(l Material Science and Engineering School, University of Science and technology beijing, beijing 100083, china2 Tangshan iron and Steel co. ltd., Tangshan 063000, china) Material Science and Engineering School University of Science and Technology Beijing Beijing 100083 China Tangshan Iron and Steel co. ltd. Tangshan 063000 China

Based on experimental data, the mathematical model of rolling force parameters of 3-roll mills was studied. The structure ofthe model was theoretically set up and the co.fficients were determined by static analysis of the data. The torque in co.tinuous rollingwas measured, and the characteristics and efficiency of 3-roll mills are investigated.

关键词： 3-roll mill force mathematical model co.d rolling wire

Thermodynamics of Slag-desulphuration in VD Process

在线全文

学校读者我要写书评

暂无评论

International Journal of Minerals,Metallurgy and Materials 2000年第1期14卷 14-17页

作者： Jisong Yi Ping Wang Jie Fu Baohong Tu Jin Li Jianxin Liu Wu Wen Chenggang Huang University of Science and technology beijing, beijing 100083, china Daye Special Steel ltd. co. University of Science and technology beijing Beijing 100083 China Daye Special Steel ltd. co. China

By means of the multi-regressing, the relationship between the sulphur-capacity of refining slag and influence factors (such as slag co.ponents, temperature) has been established for CaO-SiO_2-Al_2O_3-MgO slag-system. The real desulphur-capability of this slag and the ideal slag-quantity for desulphurization calculated by regression formula are matched to the practice,

关键词： refining-slag desulfurization thermodynamics Sulfur-capacity

Effect of co.tinuous co.ling co.ditions on Microstructure and Mechanical Properties of High Carbon Steel Rod

在线全文

学校读者我要写书评

暂无评论

International Journal of Minerals,Metallurgy and Materials 1999年第4期13卷 277-280页

作者： QingWu Cai1 Yumei Pu2 Di Tang1 Zhenli Mi1 Yuzhou Zhu2(l Material Science and Engineering School, University of Science and technology beijing, beijing 100083, china2 Maanshan iron and Steel co. ltd., Maanshan 243000, china) Material Science and Engineering School University of Science and Technology Beijing Beijing 100083 China Maanshan Iron and Steel co. ltd. Maanshan 243000 China

The effect of co.ling rate and austenitizing co.dition on the mechanical properties of high carbon steel (SWRH82B) has beeninvestigated. Specimens were made of high carbon steel rod and heat-treated by Gleeble-2000 to produce a wide variation in prior austenite size. Different co.ling rates were carried out, and then pearlite interlaminar spacing and mechanical properties were measured andtested respectively. Acco.ding to the results, it co.ld be found that under the co.tinuous co.ling with the increase of co.ling rate, tensilestrength greatly increases and reduction in area exhibits a slightly increase for an equivalent value of prior austenite grain size. Whenprior austenite size increases, reduction in area decreases, and tensile strength increases slightly for an equivalent value of pearlite interlaminar spacing. It is co.cluded that prior austenite size primarily co.trols ductility and pearlite interlaminar spacing co.trols tensilestrength. Mathematical formulae are given for these relations.

关键词： high carbon steel co.tinuous co.ling, interlaminar spacing ofpearlite, austenite grain size.