检索结果-南通市图书馆

Copper slag assisted coke reduction of phosphogypsum for sulphur dioxide preparation

Chinese Journal of Chemical Engineering 2024年第1期65卷 43-53页

作者： Dong Ma Qinhui wang State Key Laboratory of Clean Energy Utilization Institute for Thermal Power EngineeringZhejiang UniversityHangzhou 310027China

The reduction of phosphogypsum(PG)to lime slag and SO_(2)using coke can effectively alleviate the environmental problems caused by ***,the PG decomposition temperature remains high and the product yield remains *** adding additives,the decomposition temperature can be further reduced and PG decomposition rate and product yield can be ***,the use of current additives such as Fe_(2)O_(3)and SiO_(2)brings the problem of increasing economic ***,it is proposed to use solid waste copper slag(CS)as a new additive to reduce PG to prepare SO2,which can reduce the cost and meet the environmental benefits at the same *** effects of proportion,temperature and thermostatic time on PG decomposition are investigated by experimental and kinetic analysis combined with FactSage thermodynamic calculations to optimize the roasting ***,the reaction mechanism is *** is found that adding CS to the coke and PG system can increase the rate of PG decomposition and SO_(2)yield while lowering the PG decomposition *** example,when the CS/PG mass ratio increases from 0 to 1,PG decomposition rate increases from 83.38%to 99.35%,SO_(2)yield increases from 78.62%to 96.81%,and PG decomposition temperature decreases from 992.4℃to 949.6℃.The optimal reaction parameters are CS/PG mass ratio of 1,Coke/PG mass ratio of 0.06 at 1100℃for 20 min with 99.35%PG decomposition rate and 96.81%SO_(2) *** process proceeds according to the following reactions:2CaSO_(4)+ 0.7C + 0.8Fe_(2)SiO_(4)→0.8Ca_(2)SiO_(4)+ 0.2Ca_(2)Fe_(2)O_(5)+ 0.4Fe_(3)O_(4)+2SO_(2)+ 0.7CO_(2)Finally,a process for decomposing PG with coke and CS is proposed.

关键词： Phosphogypsum Sulfur dioxide Copper slag Fluidized-bed Reduction Waste treatment

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Number of Solitons Emerged in the Initial Profile of Shallow Water Using Convolutional Neural Networks

引用

Journal of Systems Science & Complexity 2024年第2期37卷 463-479页

作者： wang Zhen CUI Shikun School of Mathematical Sciences Dalian University of TechnologyDalian 116024China School of Mathematical Sciences Beihang UniversityBeijing 100191China

The soliton resolution conjecture proposes that the initial value problem can evolve into a dispersion part and a soliton ***,the problem of determining the number of solitons that form in a given initial profile remains unsolved,except for a few specific *** this paper,the authors use the deep learning method to predict the number of solitons in a given initial value of the Korteweg-de Vries(KdV)*** leveraging the analytical relationship between Asech^(2)(x)initial values and the number of solitons,the authors train a Convolutional Neural Network(CNN)that can accurately identify the soliton count from spatio-temporal *** trained neural network is capable of predicting the number of solitons with other given initial values without any additional *** extensive calculations,the authors demonstrate the effectiveness and high performance of the proposed method.

关键词： Convolutional neural network deep learning method KdV equation soliton

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Chemical characteristics of long-term acid rain and its impact on lake water chemistry:A case study in Southwest China

引用

Journal of Environmental Sciences 2024年第4期138卷 121-131页

作者： Liuyi Zhang Jiawang Shuxiao wang Chunbo wang Fumo Yang Tingzhen Li Chongqing Key Laboratory of Water Environment Evolution and Pollution Control in Three Gorges Reservoir Chongqing Three Gorges UniversityWanzhou 404000China State Key Joint Laboratory of Environment Simulation and Pollution Control School of EnvironmentTsinghua UniversityBeijing 100084China College of Carbon Neutrality Future Technology Sichuan UniversityChengdu 610065China National Engineering Research Center on Flue Gas Desulfurization Chengdu 610065China

The chemical composition of acid rain and its impact on lake water chemistry in Chongqing,China,from 2000 to 2020 were studied in this *** regional acid rain intensity is affected jointly by the acid gas emissions and the neutralization of alkaline *** pH of precipitation experienced three stages of fluctuating decline,continuous improvement,and a slight *** pH showed inflection points in 2010,mainly due to the total control actions of SO_(2)and NO_(x)implemented in *** total ion concentrations in rural areas and urban areas were 489.08μeq/L and 618.57μeq/L,*** top four ions were SO_(4)^(2-),Ca^(2+),NH_(4)^(+)and NO_(3)^(-),which accounted for more than 90%of the total ion concentration,indicating the anthropogenic *** 2010,SO_(4)^(2-)fluctuated greatly while NO_(3)^(-)continued to rise;however,after 2010,both SO_(4)^(2-)and NO_(3)^(-)began to decline rapidly,with the rates of-12.03μeq/(L·year)and-4.11μeq/(L·year).Because the decline rate of SO_(4)^(2-)was 2.91 times that of NO_(3)^(-),the regional acid rain has changed from sulfuric acid rain to mixed sulfuric and nitric acid *** lake water is weakly acidic,with an average pH of 5.86,and the acidification frequency is 30.00%.Acidification of lake water is jointly affected by acid deposition and acid neutralization capacity of lake *** deposition has a profound impact on water acidification,and nitrogen(N)deposition,especially reduced N deposition,should be the focus of future research.

关键词： Acid rain Chemical composition Neutralization Nitrogen deposition Water acidification

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

How can technology and efficiency alleviate the dilemma of economic growth and carbon emissions in China's industrial economy? A metafrontier decoupling decomposition analysis

引用

Petroleum Science 2024年第2期21卷 1415-1428页

作者： Miao wang Chao Feng School of Business Zhengzhou UniversityZhengzhou450001HenanChina School of Economics and Business Administration Chongqing UniversityChongqing400030China

This paper attempts to explore the decoupling relationship and its drivers between industrial economic increase and energy-related CO_(2) emissions(ICE). Firstly, the decoupling relationship was evaluated by Tapio index. Then, based on the DEA meta-frontier theory framework which taking into account the regional and industrial heterogeneity and index decomposition method, the driving factors of decoupling process were explored mainly from the view of technology and efficiency. The results show that during2000-2019, weak decoupling was the primary state. Investment scale expansion was the largest reason hindering decoupling process of industrial increase from ICE. Both energy saving and production technology achieved significant progress, which facilitated the decoupling process. Simultaneously, the energy technology gap and production technology gap among regions have been narrowed, and played a role in promoting decoupling process. On the contrary, both scale economy efficiency and pure technical efficiency have inhibiting effects on decoupling process. The former indicates that the scale economy of China's industry was not conducive to improve energy efficiency and production efficiency, while the latter indicates that resource misallocation problem may exist in both energy market and product market.

关键词： China's industrial sector Decoupling process Meta-frontier DEA Index decomposition method Driving factors

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

CFD-based hull optimization in calm water using adaptive grid deformation method

引用

Journal of Hydrodynamics 2024年第2期36卷 241-262页

作者： Shuguang wang Yonghwan Kim Department of Naval Architecture and Ocean Engineering Seoul National UniversitySeoulKorea

This paper presents an adaptive grid deformation technique for optimizing ship hull forms using computational fluid dynamics(CFD).The proposed method enables accurate and smooth updates of the hull surface and 3-D CFD grids in response to design *** technique incorporates a two-level point-transformation approach to move the grid points by a few design ***,generic B-splines are utilized to transform grid points according to the displacements of the control points within a defined control *** ensures surface modification accuracy and smoothness,similar to those provided by non-uniform rational ***,radial basis functions are used to interpolate the movements of the control points with a limited set of design *** developed method effectively maintains the mesh quality and simulation *** applying this method to surface and grid adaptation,a regression model is proposed in the form of a second-order polynomial to represent the relationship between the geometric parameters and design *** polynomial is then used to introduce geometric ***,a radial basis function surrogate model for the calm-water resistance is constructed to approximate the objective *** enhanced optimization framework is proposed for CFD–based hull optimization and applied to KVLCC2 to validate its feasibility and efficiency.

关键词： Hull-form optimization adaptive grid deformation ship resistance OpenFOAM radial basis function(RBF)surrogate model

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

New steelmaking process based on clean deoxidation technology

引用

International Journal of Minerals,Metallurgy and Materials 2024年第6期31卷 1249-1262页

作者： Zhongliang wang Yanping Bao State Key Laboratory of Advanced Metallurgy University of Science and Technology BeijingBeijing 100083China

After the converter steelmaking process,a considerable number of ferroalloys are needed to remove dissolved oxygen from the molten steel,but it also forms a lot of oxide inclusions that cannot be completely *** the same time,it increases the carbon emis-sions in the steel production *** years of research,our team have developed a series of clean deoxidation technologies,includ-ing carbon deoxidation,hydrogen deoxidation,and waste plastic deoxidation of molten steel to address the aforementioned *** this study,thermodynamic calculations and laboratory experiments were employed to verify that carbon and hydrogen can reduce the total oxygen content in the molten steel melt to below 5×10^(-6) and 10×10^(-6),*** analysis of the deoxidation mechanisms and ef-fects of polyethylene and polypropylene was also *** addition,the applications of carbon deoxidation technology in different steels with the hot-state experiment and industrial production were discussed *** carbon deoxidation experimental results of different steels were as follows:(1)the oxygen content of bearing steel was effectively controlled at 6.3×10^(-6) and the inclusion number density was lowered by 74.73%compared to aluminum deoxidized bearing steel;(2)the oxygen content in gear steel was reduced to 7.7×10^(-6) and a 54.49%reduction of inclusion number density was achieved with almost no inclusions larger than 5μm from the average level of industry gear steels;(3)a total oxygen content of M2 high-speed steel was as low as 3.7×10^(-6).In industrial production practice,car-bon deoxidation technique was applied in the final deoxidation stage for non-aluminum deoxidized bearing steel,and it yielded excellent results that the oxygen content was reduced to below 8×10^(-6) and the oxide inclusions in the steel mainly consist of silicates,along with small amounts of spinel and calcium aluminate.

关键词： clean deoxidation carbon deoxidation hydrogen deoxidation waste plastics deoxidation

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Achieving high strength and rapid degradation in Mg-Gd-Ni alloys by regulating LPSO phase morphology combined with extrusion

引用

Journal of Magnesium and Alloys 2024年第6期12卷 2312-2326页

作者： Kai Ma Jingfeng wang Yinhong Peng Chaoneng Dai Yuanlang Pan Ye wang Danqian wang Jinxing wang Yanlong Ma Fusheng Pan College of Materials Science and Engineering Chongqing UniversityChongqing 400044PR China National Engineering Research Center for Magnesium Alloys Chongqing 400044PR China College of Chemistry and Chemical Engineering Chongqing UniversityChongqing 401331PR China College of Materials Science and Engineering Chongqing University of TechnologyChongqing 400054PR China

In this study,Mg-13.2Gd-4.3Ni alloys containing continuous bulk-shaped long-period stacking ordered(LPSO),lamellar LPSO,and a small amount of eutectic phase were prepared,and the evolution of microstructure at different extrusion temperatures and its influence on mechanical and degradation properties as well as corrosion mechanism were *** before extrusion can effectively promote the precipitation of lamellar LPSO in ***400 with higher volume fraction of non-DRXed grains exhibited higher strength,which was mainly due to strong texture,high dislocation density,and high volume fraction of lamellar *** EX420 with higher volume fraction of DRXed grains showed higher degradation rate,which was mainly due to the higher density of grain *** EX400 exhibited excellent comprehensive properties with tensile yield strength(TYS)of 334 MPa,ultimate tensile strength(UTS)of 484 MPa and elongation(EL)of 7.4%,ultimate compressive strength(UCS)of 638 MPa and compressive yield strength(CYS)of 443 MPa,degradation rate of 86.1 mg/cm^(2)/h at 93℃in 3 wt.%KCl solution.

关键词： Mg-Gd-Ni alloys LPSO Mechanical properties Degradation rate

来源：

维普期刊数据库

同方期刊数据库评论

在线全文

学校读者我要写书评

暂无评论

Numerical simulation and parameter optimization of Coriolis force scale measurement process based on DEM

引用

Particuology 2024年第7期90卷 128-139页

作者： Haiting Liu Yong Yang Xiangliang wang Jiewen Deng Bingbing wang School of Energy and Power Engineering Northeast Electric Power UniversityJilin132012China CNBM Hefei Mechanical&Electrical Engineering Technology Co.Ltd Hefei230051China

The Coriolis force method is a recently developed and highly regarded direct measurement technique that enables high-precision measurement of bulk *** operational parameters and variations thereof directly influence the measurement accuracy of the *** this study,a measurement correction coefficient is introduced to improve the calculation method for mass flow rate of the *** DEM is employed to simulate the motion of particle groups within the Coriolis force scale under different parameters,and the effects of various structural and operational parameters on the measurement results are *** research findings indicate that a lower rotational speed leads to more stable instantaneous measurement results,although the measurement error is relatively *** the rotational speed exceeds 300 rpm,the measurement error remains within 15%.For materials with a radius of 1–2 mm,the variation range of precision error is approximately 0.4%.Among the structural parameters,the radius of the measurement wheel has the most significant impact on the measurement results,wherein a larger measurement wheel radius corresponds to a smaller measurement *** horizontal angle of the blades follows as the next influential parameter,with a clockwise rotation and a horizontal angle of 30°resulting in a measurement error below 2%.

关键词： Parameter optimization Discrete element method Coriolis force scale Measurement error Numerical simulation

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Insight into the adsorption behavior and mechanism of trace impurities from H_(2)O_(2) solution on functionalized zirconia by tuning the structure of amino groups

引用

Frontiers of Chemical Science and Engineering 2024年第5期18卷 83-94页

作者： Yu Meng Yitong wang Guozhu Li Guozhu Liu Li wang Key Laboratory for Green Chemical Technology of Ministry Education School of Chemical Engineering and TechnologyTianjin UniversityTianjin 300072China Haihe Laboratory of Sustainable Chemical Transformations Tianjin 300192China

Primary,secondary and tertiary amino-functionalized zirconia(ZrO_(2)-NH_(2),ZrO_(2)-NH and ZrO_(2)-N)was synthesized by the postgrafting method for the adsorption removal of typical metallic ions,phosphate and total oxidizable carbon from a real H_(2)O_(2) ***_(2)-NH_(2),ZrO_(2)-NH and ZrO_(2)-N exhibited similar pore sizes and sequentially increased zeta *** adsorption results of single and binary simulated solutions showed that the removal efficiency increased in the order of Fe^(3+)>Al^(3+)>Ca^(2+)>Na^(+).There is competitive adsorption between metallic ions,and Fe^(3+) has an advantage over the other metals,with a removal efficiency of 90.7%.The coexisting phosphate could promote the adsorption of metallic ions,while total oxidizable carbon had no effect on *** adsorption results of the real H_(2)O_(2)solution showed that ZrO_(2)-NH_(2) exhibited the best adsorption affinity for metallic ions,as did phosphate and total oxidizable carbon,with a total adsorption capacity of 120.9 mg·g_(-1).Density functional theory calculations revealed that the adsorption process of metallic ions involves electron transfer from N atoms to metals and the formation of N-metal bonds.

关键词： adsorption metallic ion phosphate total oxidizable carbon zirconia H_(2)O_(2)

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

Self-assembled VS_(2) microflowers buffering volume change during charging and discharging towards high-performance zinc ion batteries

引用

Journal of Materials Science & Technology 2024年第6期173卷 107-113页

作者： Tingsheng wang Wujie Gao Yuanxi Zhao Songcan wang Wei Huang Frontiers Science Center for Flexible Electronics Xi’an Institute of Flexible Electronics(IFE)Northwestern Polytechnical UniversityXi’an 710072China Key Laboratory of Flexible Electronics of Zhejiang Province Ningbo Institute of Northwestern Polytechnical UniversityNingbo 315103China School of Materials Science and Engineering Northwestern Polytechnical UniversityXi’an 710072China

VS_(2) has attracted increasing attention as a cathode material for aqueous zinc ion batteries because of its proper large layer spacing,weak interlayer interactions,multiple valence states of V,and excellent electrical conductivity,but its large volume change during charging and discharging leads to poor cycling ***,we report a one-step hydrothermal synthesis of VS_(2) microflowers with proper lamellar spacing,which provides a stable framework for the insertion/deinsertion of zinc ions and enhances the cycling stability,delivering an initial charge capacity of 128.3 mAh g^(-1) at 3 A g^(-1) and maintains a charge capacity of 100.1 mAh g^(-1) after 900 *** addition,the optimized VS_(2) cathode shows specific capacities of 215.7 and 150.5 mAh g^(-1) at the current densities of 0.1 and 2 A g^(-1),respectively,demonstrating that the microflower structure with a high specific surface area and a short diffusion distance also significantly enhances the rate performance.

关键词： Vanadium sulfide Microflower Zinc ion batteries Cathode materials Volume change

来源：

维普期刊数据库评论

在线全文

维普期刊数据库

学校读者我要写书评

暂无评论

欢迎您,

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案：

请选择收藏分类：

通借通还

欢迎您,

建议与咨询 留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

时间限定

文献类型

馆藏选择

核心期刊

语言

文献类型

帮助

文字说明：

检索规则说明：

检索范例：

分类表

所选分类

限定检索结果

文献类型

馆藏范围

日期分布

学科分类号

主题

机构

作者

语言

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

在线全文

请选择保存的检索档案： 新增检索档案 确定 取消

请选择收藏分类： 新增自定义分类 确定 取消

通借通还

建议与咨询留下您的常用邮箱和电话号码，以便我们向您反馈解决方案和替代方法

请选择保存的检索档案：

请选择收藏分类：